Alexor PC9155D-433 Installationsanleitung PDF herunterladen (Seite 22)

PC9155 Wireless Alarm System

4-2

• Digit 1 selects one of the following zone definition options for the first 8 zones. A ‘0’ in the digit 1 location

indicates that the default settings for the first 8 zones are in place unless overridden during enrollment. See section [001] for defaults.

Step

Once in the programming section, the 4-digit number “0111” is displayed. Enter

to accept the existing default programming.

See the tables below for details of Digit 1, 2, 3 and 4.

Step

After entering ‘0001’, the first telephone entry is dis played. Enter the monitoring station

telephone number after the “D”. Do NOT delete a ny of the remaining “Fs”

E.g., To enter 02-1234-5678:

Press followed by

to complete the entry. See section [301] for additional details.

Step

After programming the first telephone number, the system account code is displayed.

The system account code can be any 6-digit combination of numbers (0-9) and letters (A-

F). If the system account code is 4-digits, the last two digits must be ‘FF’.

To enter the letters A through F, press then the numbers 1 through 6 for the letter A

through F respectively. Press again to revert back to decim

al entry.

E.g.,: To enter “1234FF” Press .

See section [310] for additional details.

Step

After programming the system account code, the downloading access code is displayed.

Enter the new downloading access code or press to proceed to the next step. See

section [403] for additional details.

Step

The entry delay is the amount of time given to disarm the alarm system, after entering the

premises through a delay type zone, before an alarm is sounded.

• Press to accept the default time of 30 seconds (030) or enter an entry

delay between 001 and 255.

E.g., Press 020 for a delay of 20 seconds. See section [005] for additional details.

Step

The exit delay is the amount of time given to exit the premises after pressing the Arm key

before the alarm system is armed.

• Press to accept the default time of 120 seconds (120) or enter an entry

delay between 001 and 255.

E.g., Press 030 for a delay of 30 seconds. See section [005] for additional details.

Step

After programming the exit delay, the installer code is displayed. Enter a 4 or 6-digit code

depending on the value in section [701] option 5.

Press to exit Template Programming.

See section [006] for installer code details.

Option Zn1 Zn2 Zn3 Zn4 Zn5 Zn6 Zn7 Zn8 Zone Definitions (Options 1- 7)

0 This entry will not change the currently programmed zone definitions.

1 01 03 03 03 04 04 04 04 01 Delay 1

2 01 03 03 05 05 05 05 88 02 Delay 2

3 01 03 03 05 05 05 05 87 03 Instant

4 01 01 03 03 03 03 03 03 04 Interior

5 01 03 03 06 05 05 05 05 05 Interior Stay/Away

6 01 03 03 06 05 05 05 88 06 Delayed Stay/Away

7 01 01 06 06 06 01 01 01 87 Delayed 24 Hr.

Refer to Chapter 5 for zone definition details 88 Standard 24 Hr. Fire

Enter Data

1110

D FFFFFFFFFFFFFF

FFFFFFFFFFFFFFFF

D0212345678 FFFF

FFFFFFFFFFFFFFFF

Enter Hex Data

FFFFFF

Enter Hex Data

1234FF

Enter Hex Data

155009

Enter Data

300

Enter Data

201

Enter Data

5555

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 87 88

Kommentare zu diesen Handbüchern

Keine Kommentare

Alexor PC9155D-433 Installationsanleitung Seite 22

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Alexor PC9155D-433