Alexor PC9155D-433 Installationsanleitung PDF herunterladen (Seite 66)

PC9155 Wireless Alarm System

5-42

[701] First International Options Code

[702] Second International Options Code

[703] Delay Between Dialing Attempts

For standard (force) dialing, the panel will go off-hook, search for a dial tone for 5 seconds, and hang up for 20 seconds. This programmable timer adds a delay

before the next call is attempted, and is defaulted to 003 to make a total of 8 seconds before the panel makes the next dialing attempt.

[800] Door Chime Options for Zones 1-34

Option Description

[1]

ON: 50 Hz AC. The incoming AC power cycles at 50 Hz.

OFF: 60 Hz AC. The incoming AC power cycles at 60 Hz.

[2]

ON: The time base is the internal crystal oscillator. The internal crystal is used for the time base instead of AC power.

OFF: The time base is the AC power input. The 50 or 60 Hz AC power is used for the time base.

[3]

ON: AC/DC Arming Inhibit with Battery Check Enabled. When an AC or battery trouble is present, the system will not arm. This includes key-

pad, keyswitch, No Activity Arming and downloading arming.

OFF: Arming not Inhibited. The system can be armed, with an AC trouble or Battery trouble present. System battery is not checked upon arming.

[4]

ON: System Tampers Require Installer Reset and Inhibit Arming. If any system tamper condition occurs, the Installer code must be entered

([

][8][Installer Code]) and the tamper condition must be restored before the system can be armed. This also includes no-activity arming and key-

switch.

OFF: System Tampers Do Not Require Installer Reset. If any system tamper condition occurs, installer reset is not required.

[5]

ON: 6-digit Access Codes. All access codes on the system must be 6 digits in length. If this option is selected, 2 digits are added to the end of each

code, the first 4 digits of the existing codes will remain programmed.

System Master Code = XXXX56

Installer Code = YYYY55

Access Codes 1-16 = ZZZZ00

OFF: 4-digit Access Codes. All access codes on the system are 4 digits in length except the Panel I.D. code and the Downloading Access code,

which are always 6 digits. For any existing codes, the last 2 digits are removed.

[6]

ON: Busy Tone Detection Enabled. If a busy tone is detected, the panel will hang-up and attempt to communicate following the “Delay Between

Dialing Attempts”.

OFF: Busy Tone Detection Disabled. The communicator will use the standard dialing procedure for every communication attempt regardless of a

busy line.

[7]-[8]

For Future Use

Option Description

[1]

ON: Pulse Dialing Make/Break Ratio is 33/67. This ratio is used for Europe.

OFF: Pulse Dialing Make/Break Ratio is 40/60. This ratio is used in North America.

[2]

ON: Force Dialing Enabled. If the first communication attempt made by the panel fails, on every subsequent attempt the panel will dial regardless of

the presence of a dial tone.

The panel will go off-hook, search for a dial tone for 5 seconds, hang-up for 20 seconds, go off-hook, search for dial tone for 5 seconds, and then dial

(assuming no presence of dial tone).

OFF: Force Dialing Disabled. The panel does not dial the programmed telephone number if the dial tone is not present.

[3]

For Future Use

[4]

ON: 1600 Hz Handshake. The communicator responds to a 1600 Hz handshake for pulse formats.

OFF: Standard Handshake. The communicator responds to the handshake designated by the pulse format selected (1400 or 2300Hz).

[5]

ON: I.D. Tone Enabled. After the telephone number is dialed, the panel emits a tone (as specified by option 6) for 500ms every two seconds to indi-

cate that it is a digital equipment call, not voice.

OFF: I.D. Tone Disabled. The panel does not emit a tone.

[6]

ON: 2100 Hz I.D. Tone. A 2100Hz ID tone is used for option [5] above.

OFF: 1300 Hz I.D. Tone. A 1300Hz ID tone is used for option [5] above.

[7]-[8]

For Future Use

If this value is 00 or FF, the default will be 8 seconds (3 programmable, plus the 5 second delay), otherwise it uses the programmed value.

Keypads and indoor sirens can annunciate one of four different door chime tones for each zone on the system.

Each section contains the following chime options:

• Enable one door chime option for each zone.

• If more than one option is enabled, the highest numerical option enabled takes precedence.

For example: If options 3 and 1 are both enabled, then the zone will sound option 3 ‘Ding-Dong’.

• If all door chime options are disabled, the keypad/siren will not sound a door chime tone for that particular zone.

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 87 88

Kommentare zu diesen Handbüchern

Keine Kommentare

Alexor PC9155D-433 Installationsanleitung Seite 66

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Alexor PC9155D-433