Alexor PC9155G-868 Installationsanleitung PDF herunterladen (Seite 69)

6 Testing & Troubleshooting

6-3

Alternate Comm Receiver

Trouble

This condition is generated when the GPRS/

Ethernet module loses supervision or fails to

initialize a receiver.

• Refer to the TL260/TL260GS/TL265/TL265GS/GS2060/GS2065

Installation Manual for more details.

Alternate Comm Fault This condition is created when the PC9155

loses communication with an Ethernet or

GPRS module.

• Refer to the TL260/TL260GS/TL265/TL265GS/GS2060/GS2065

Installation Manual for more details.

Alternate Comm Config

SMS Trouble

This condition is created when the GPRS/

Ethernet module detects an SMS Connect 24

Configuration failure trouble.

• Refer to the TL260/TL260GS/TL265/TL265GS/GS2060/GS2065

Installation Manual for more details.

Trouble [1] Service Required Press [1] to determine specific trouble

Low Battery

Main panel battery less than 11.4V +/- 0.1V.

NOTE: This trouble condition will not clear

until the battery voltage is 12.5V

+/- 0.1V.

NOTE: If battery is new allow 24 hrs. to charge.

• Verify voltage measured across AC terminals is 16-18 VAC.

• Verify voltage measured across battery terminals is 12.5V +/- 0.1V.

• Replace transformer if required.

• Disconnect then reconnect battery leads.

General System Trouble

The system has detected the presence of a RF

Jam for 20 seconds or communications with

the wireless receiver have failed causing a

hardware fault.

• Check Event Buffer to determine specific trouble.

• If buffer logs RF Jam trouble, check for external 433MHZ signal

sources. To disable RF Jam, enable option [7] in program section

[804] subsection [900].

• If buffer logs “Hardware Fault” - replace panel.

General System Tamper

Cover tamper tripped.

• Verify tamper buttons are installed into backplate and frontplate,

and that the frontplate is fully in place.

• Verify panel is properly secured to wall with the front cover on.

Trouble [2] AC Failure

AC Failure No AC at panel AC input terminals.

• Verify voltage measured across AC terminals is 16-18VAC.

Replace transformer if required.

Trouble [3] Telephone Line Trouble

Telephone Line Trouble Phone line voltage at TIP, RING on main

panel less than 3V

DC.

Measure voltage across TIP and RING on the panel:

• No phone off-hook – 50VDC (approx.).

• Any phone off-hook – 5VDC (approx.).

Wire incoming line directly to TIP and RING.

• If trouble clears, check wiring or the RJ-31x phone jack.

Trouble [4] Failure to Communicate

Failure to Communicate

Panel fails to communicate one or more

events to central station.

Connect a handset to TIP and RING of the control panel. Monitor

for the following conditions:

Continuous dial tone

• Reverse TIP and RING.

Recorded operator message comes on

• Verify correct phone number is programmed.

• Dial the number programmed using a regular telephone to deter-

mine if a [9] must be dialed or if 800 service is blocked.

Panel does not respond to handshakes

• Verify the format programmed is supported by the central station.

Panel transmits data multiple times without receiving a hand-

shake

• Verify account number and reporting codes are correctly pro-

grammed.

Contact ID and Pulse formats

• Program a HEX [A] to transmit a digit [0].

SIA format

• Program a digit [0] to transmit a digit [0].

GSM/Ethernet

• Refer to the TL260GS/TL265GS/GS2060/GS2065 Installation

Manual for troubleshooting actions.

1 2 ... 64 65 66 67 68 69 70 71 72 73 74 ... 79 80

Kommentare zu diesen Handbüchern

Keine Kommentare

Alexor PC9155G-868 Installationsanleitung Seite 69

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Alexor PC9155G-868